Pipe and Fittings
Central Vacuums > Pipe and Fittings
Showing 1 - 18
of results
|
|
![]() View Large Image | short 90 Use this fitting at the mounting plates only. Since this is the sharpest turn in the system, potential clogging will occur with easy access - right at the inlet valve!
|
![]() View Large Image | 90 Sweep PVC Vacuum Connector Probably the most used item. Remember this can not be used behind the inlet bracket--use the short 90 instead
|
![]() View Large Image | 90 Spigot PVC Vacuum Connector Spigot fittings are made to fit directly into other fittings. This will prove helpful in tight spots!
|
![]() View Large Image | 45 EL We suggest using 45's, even two of them when possible, to use less 90's. When the pipe line needs to run up or down, angle a 90 at 45-degrees into a 45 fitting
|
![]() View Large Image | 45 Spigot PVC Vacuum Connector Spigot fittings are made to fit directly into other fittings. This will prove helpful in tight spots!
|
![]() View Large Image | 90 Sweep Tee PVC Vacuum 3-way Connector For connecting a branch to the main line. Be sure the airflow is adequate. Do not install the tee backwards!
|
![]() View Large Image | 45 Wye PVC Vacuum 3-way Connector For connecting a branch to the main line. Be sure the airflow is adequate. Do not install the wye backwards!
|
![]() View Large Image | Stop Coupler For connecting two pieces of pipe together. If you need a case, enter 175 for the quantity.
|
![]() View Large Image | 3-in-1 Mounting Bracket PVC Most popular bracket for all Basic Inlet Valve Covers. For new construction nail it to a stud. For existing home installation cut the stud side off and set it in a 2x4" drywall cutout. When piping, connect a fitting such as a tight 90 or coupling to the f
|
![]() View Large Image | Exhaust Vent Door for Central Vacuum Pipe Installed on the outside of the home to exhaust the power unit. This is not needed with M.D.'s bag type units. Fits 2" OD (Vacuum PVC Pipe). Overall size is 3-5/8"w X 4-5/8"h
|
![]() View Large Image | Inlet Blank Cover Plate, (3 in a pack) Three cover plates come in one package. Use the cover plate to cover up a old vacuum hole in the sheet rock or to gain access into a wall. The dimensions are 4-3/4" tall by three inches wide. Screw holes on center are 3-7/8" apart from each other at 12 an
|
![]() View Large Image | Inlet Valve Extension Use as many of these as needed when the wall, for any reason, is too thick causing the mounting plate and finished plate to not meet. Longer screws will be needed as well. It adds 3/4 of an inch to the cover plate. If that is too much you can cut to size.
|
![]() View Large Image | Install Kit with 1 Electric Inlet Includes the following items pictured. Add pipe (24ft recommended). Buy regular PVC cement from a local store. Includes inlet valve and backing plate. The included 25ft of wire is low voltage and runs from the faceplate to the vacuum canister to turn it o
|
![]() View Large Image | Install Kit with 1 non-Electric Inlet Includes the following items pictured. Add pipe (24ft recommended). Buy regular PVC cement from a local store. Includes a square door inlet valve and backing plate. The included 25ft of wire is low voltage and runs from the faceplate to the vacuum caniste
|
![]() View Large Image | J shaped Pipe Hanger Used to hang 2" OD Central Vacuum Pipe at a distance of a foot or less. Comes with a nail. Make of sturdy PVC. The pipe snaps into the J and looks real clean
|
![]() View Large Image | Muffler for vacuum fits 2-inch OD exhaust ports Is your power unit too loud? Decrease that irritating sound by inserting this muffler into any central vacuum that has 2" OD diameter exhaust ports. One muffler per exhaust port on the vacuum itself. Use a 90 Spigot Sweep to install it vertically if desir
|
![]() View Large Image | Pipe hanger Used to hold 2" OD Central Vacuum Pipe in position
|
![]() View Large Image | Supervalve Mounting Bracket Includes 110v wire connector No inlet included
|