|
|
Roller Brush for Stealth
Bristles new are 7/16" long.
This fits the Lindhaus also labeled Stealth powerhead. Comes as the brush
roll only, no shaft.
Available
in 12" and 14" lengths.
|
|
|
|
Cord for Stealth or Central Vacuum Cleaner
This a direct replacement for the
Stealth (Lindhaus) Vacuum Brush.
It is
also a direct replacement cord for many central vacuum cleaners.
Cord is 39 inches long.
|
|
|
|
Swivel Neck for Stealth
Swivel Neck for Stealth (Lindhaus) Powerhead
This
part need to be replaced when the wand (when turned) is able to be turned
completely around. It also prevents the neck from being pulled out from
the powerhead.
|
|
|
|
Complete Neck Joint & Cord for
Stealth (Lindhaus)
Complete Neck Joint & Cord for Stealth
This part comes with the cord & and swivel neck as listed on this page
|
|
|
|
Neck
Stop cord Bracket for Stealth (Lindhaus) powerhead
Neck Stop cord Bracket for Stealth
This
prevents the neck from being pulled out of the powerhead. Also comes with
a rubber grommet to secure the cord.
|
|
|
|
Stealth
(Lindhaus) Bottom Brush Shoe Plate
Available to fits either the 12" or 14" wide Stealth brush and goes under
the roller brush. It is attached with five screws.
|
|
|
|
Central Vacuum Wireless Remote Control
(RF)
The new 3-piece central vacuum remote control allows you to use your central vacuum unit without running low voltage wire. This set-up can be used in a new construction or existing home. The remote control set-up enables you to activate your vacuum unit in any existing home where the low voltage wire is no longer working properly. There are many reasons why low voltage wire stops working...
* Inadequate installation.
* Wires may rot or come loose over time.
* Someone in the attic accidentally tripping on a wire.
* Rats eating through the wire.
And countless other reasons.
Outside of the many reasons why existing homes may need this set-up, there are many instances where the low voltage wire was never installed before the walls went up, making it virtually impossible to install the wire. Home owners may also simply want the convenience of a remote control system, without the worries of installing low voltage wire
Simply attach remote on the vacuum hose handle and other components
near the vacuum power unit.
Range is similar to a vehicle remote lock/unlock key fob - about 150 feet
depending on wall thickness and number. A small transmitter plugs into
120v and hangs near the vacuum unit and wire connects to the vacuum unit
from it. Use this remote clicker to activate the vacuum on and off.
|
|
|
|
Gas Pump Handle for Vacuum Hose
Comes complete with handle, short metal tube,
bleeder valve, new seal and replacement screws. Fits on
hoses with a gas pump handle design as pictured.
Does not include
switch or wires but requires switch that rocks left and right not forward
and back.
Not compatible with Beam hoses
|
|
|
|
Switch Assembly for Gas Pump Handle
Comes complete as scene in picture. Includes switch assembly, seal, and
screws.
This
is a 3-position switch assembly. Fits hose
handles that look exactly like the one pictured
|
|
|
|
Pistol Grip Handle for Vacuum Hose
Replaces the handle and short metal tube (not
pictured) on
hoses with a pistol grip handle design exactly as pictured.
Does not include switch or wires but requires switch that
rocks left and right not forward and back.
We
would suggest that you purchase the Gas Pump handle (pictured above)
instead, it is much more comfortable in your hand.
Not compatible with Beam hoses
|
|
|
|
Switch Assembly for Pistol Handle
Replaces the 3-position switch assembly in hose
handles that look exactly like picture above. (pistol grip)
Item is
about 14 inches long
|
|
|
|
8ft Cord for Electric Hose (cuff and plug cord)
This is a hose conversion kit and replacement
kit. Replaces the two prong direct connect assembly or an existing broken
cord assembly on electric hoses with an electrical cord on the wall end.
The two included cuffs (only one in picture) cover an older or newer hose.
Includes:
* Two cuffs (only one in picture)
* Cord (with molded-in fuse)
* One male pin connection
* One female slate connection
Older hoses have two male pins and will need to be converted.
Instructions are included
|
|
|
|
Fuse Plug for Electrical Hose (cuff and 2-pin plug
This is a hose conversion kit and/or replacement
kit.
Can
be purchased to replace the pigtail cord assembly with direct
connect or to replace an existing broken assembly on
electric hoses that have a 2-pin direct connection to plug into the
inlet.
Includes:
Two slide-on cuffs (older and newer styles)
One 2-pin plug (with molded-in fuse)
One male pin connection (connects to the yellow hose wire)
One female slate connection (connects to the white hose wire)
Instructions
|
|
Web Site Solutions